BM-PH1723

Energy Saving Modules

Voltage Requirements :
Typical Extraction :

Compatible With DD1700+ and DD2300+

EIPL Bolt-On, Heat Recovery Modules
The BM-PH1723 (Bolt-On Pre-Heat Module) and BM-PC1723 (Bolt-On Post-Cool Module) have been specifically designed to integrate with the new range of DD+ dehumidifiers.
Both modules provide an effective way to improve energy efficiency by recovering and reusing heat that would otherwise be wasted.
The modules can be purchased alongside the dehumidifier as part of the initial installation or retrofitted at a later date.

BM-PH1723
Part Number 1082050
Height (in) 68
Width (in) 27
Depth (in) 35
Weight(lbs) 242
Voltage 220
Phase 1
Frequency(Hz) 60
Current(A) 1
Power(kW) 0.25
Process Air Duct Inlet (in) N/A
Process Air Duct Outlet (in) N/A
Regen Air Duct Inlet - Wet Air (in) 20 x 14
Regen Air Duct Outlet (in) 8
Typical Energy Efficency (%) 75-80
Typical DD1700+ Heat Recovery Saving (kW) 2.6
Typical DD2300+ Heat Recovery Saving (kW) 3.8
BM-PH1723
Part Number 1082050
Compatiable With DD1700+ Y
Compatiable With DD2300+ Y
Typical DD1700+ Heat Recovery Saving (kW) 2.6
Typical DD2300+ Heat Recovery Saving (kW) 3.8
BM-PH1723

1x BM-PH1723 Pre Heat Energy Saving Module
1x BM-PH1723 Owners Manual

Two Ways to Improve the Efficiency of Desiccant (Adsorption) Dehumidifiers

The energy efficiency of desiccant dehumidifiers can be improved by recovering and reusing heat energy through two methods:
‍1. Pre-heating the Regeneration Air
Pre-heat the incoming regeneration air by passing it through a heat exchanger that utilises the hot regeneration air leaving the dehumidifier.
This process recovers waste heat from the regeneration exhaust, reducing the additional energy required to heat the regeneration air to the required temperature.
‍2. Post-cooling the Process Air
Post-cool the hot, dry process air leaving the dehumidifier by passing it through a heat exchanger against the incoming return air from the conditioned space.
This transfers heat from the dry process air to the incoming return air, reducing the temperature of the supply air delivered to the conditioned space. This minimises the additional cooling required within the space while recovering otherwise wasted heat energy.
‍Overall Benefit
Both methods improve the overall energy efficiency of the dehumidifier by recovering and reusing heat that would otherwise be wasted. This helps reduce the additional heating and cooling energy required by the system.
________________________________________
‍EIPL Bolt-On, Heat Recovery Modules
The BM-PH1723 (Bolt-On Pre-Heat Module) and BM-PC1723 (Bolt-On Post-Cool Module) have been specifically designed to integrate with the new range of DD+ dehumidifiers.
Both modules provide an effective way to improve energy efficiency by recovering and reusing heat that would otherwise be wasted.
The modules can be purchased alongside the dehumidifier as part of the initial installation or retrofitted at a later date.
The DD+ units have been designed with future expansion in mind, allowing straightforward configuration and integration should either module be installed at a later stage.

Typical Energy savings can be see on the following tables..

Typical Heat Recovery Savings

Pre-Heat (kW) Post-Cool (kW)
BM-PH1723 BM-PC1723
DD1700+ 2.6 7.8
DD2300+ 3.8 9.4

Typical Energy Efficency

Pre-Heat (%) Post-Cool (%)
BM-PH1723 BM-PC1723
DD1700+, DD2300+ 75 - 80 75 - 80

BM-PH1723 – Installation and Connections
The BM-PH1723 module incorporates an integral condensate pump and therefore requires a 10mm I/D hose to be connected to a suitable drainage point.
The module also incorporates additional temperature and humidity sensors, together with a filter monitoring sensor. These provide the dehumidifier with additional information to monitor operating conditions and filter status.
Power and sensor connections are provided via a plug-and-socket arrangement, allowing quick and straightforward connection to the compatible DD+ dehumidifier.

Request a quote…

Thank you! Your submission has been received!
Oops! Something went wrong while submitting the form.